Sonance Speaker 91652 User Manual

I N S T R U C T I O N M A N U A L  
S O N A N C E C I N E M A ® S E R I E S  
I N - W A L L S P E A K E R S  
Left & Right Surround  
Speakers  
Place the left & right surround  
speakers directly to the sides of  
the listening position, between  
5 and 7 feet off the floor.  
Introduction  
Thank you for purchasing Sonance Cinema® Series in-wall speak-  
ers. When properly installed, these speakers will deliver film  
soundtracks and music with outstanding clarity and realism, even  
in the largest home theater rooms. This manual covers the  
Sonance Cinema Series LCR1, LCR2, SUR1 and SUR2 models.  
5' – 7'  
Use Figure 2 as a guide.  
Box Contents  
Surround Back  
Channel Speakers  
The surround back speakers in  
a 6.1- or 7.1-channel system  
should be placed on the rear  
wall between 4 feet and 8 feet  
apart, at least 5 feet from the  
floor. Use Figure 3 as a guide.  
Each Sonance Cinema Series speaker box contains the following:  
(1) Cinema Series LCR or SUR speaker  
(1) Paintable grille  
(1) Allen wrench  
(1) Mounting cutout template  
FIGURE 2: LEFT & RIGHT  
SURROUND SPEAKER PLACEMENT  
Speaker Placement  
NOTE: CINEMA SPEAKERS CAN BE ORIENTED EITHER VERTICALLY OR  
HORIZONTALLY WITH NEARLY IDENTICAL PERFORMANCE. WHEN ORI-  
ENTING THE CINEMA SUR1 AND SUR2 HORIZONTALLY, ROTATE  
THE MIDRANGE/TWEETER PANEL 90° (SEE STEP 5, ON PAGE 2).  
Left, Center & Right Channels  
• Place the left & right speakers on either side of the video  
screen, anywhere from 6 feet to 10 feet apart and 38 – 42  
inches from the floor. The speakers should be at least 18  
inches away from the side walls.  
4' – 8'  
5' – 7'  
• If possible, locate the center speaker at the same height as the  
left & right channel speakers (38 – 42 inches from the floor).  
• If you must place the center speaker above or below a video  
screen, place it no more than 2 feet above or below the center  
of the left and right speakers. This will maintain consistent  
tonality between all 3 front channel speakers.  
FIGURE 3: SURROUND BACK SPEAKER PLACEMENT  
• The main listening position should be between 8 and 12 feet away  
from the speakers.  
Before Installation  
Use Figure 1 as a guide.  
1. Determine the location for the speaker (see Speaker  
Placement).  
2. Perform an obstruction survey to be certain that there are no  
studs, conduit, pipes, heating ducts, pocket doors or air  
returns in the wall cavity that will interfere with the speaker.  
6' – 10'  
18"  
From Side  
Wall  
18"  
From Side  
Wall  
Apart  
3. The cutout for Cinema LCR1 and SUR1 speakers is  
7 ½" x 20½" (191mm x 521mm). The cutout for Cinema  
LCR2 and SUR2 speakers is 7 ½"  
x
33 ½" (191mm  
x
851mm). There must be at least 3 7/8” (98mm) depth within  
the wall cavity for the speaker.  
2'  
(max.)  
4. Position the included cutout template where the speaker is to  
be located and pencil an outline on the wall.  
• If you are unsure about obstructions, drill 2 – 4 small holes  
along the outlines centerline and insert a coat hanger wire  
into each hole to feel-around for possible obstructions.  
FIGURE 1: LEFT, CENTER & RIGHT SPEAKER PLACEMENT  
1
 
®
SONANCE CINEMA SERIES  
Specifications (continued)  
SUR1  
Tweeter:  
Two 1" (25mm) silk domes, ferrofluid-  
cooled  
Midrange:  
Two 3” (76mm) carbon fiber/  
Rohacell® laminated cones with  
rubber surrounds  
Woofer:  
Two 5¼" (133mm) carbon fiber/  
Rohacell® laminated cones with  
rubber surrounds  
Remove Screws  
Frequency Response:  
Impedance:  
70Hz – 20kHz 3dB  
6 ohms nominal; 4 ohms minimum  
5 watts minimum; 150 watts maximum  
90dB SPL (2.83V/1 meter)  
Perforated steel  
Power Handling:  
Sensitivity:  
Grille Material:  
Dimensions (W x H x D): 8 7/8" x 21¾" x 3 7/8"  
Rotate Panel and  
(225mm x 553mm x 98mm)  
Replace Screws  
Cutout Dimensions (W x H): 7 ½" x 20½" (191mm x 521mm)  
FIGURE 7: ROTATING THE MIDRANGE/TWEETER PANEL  
Shipping Weight:  
19 lbs (8.6kg) each  
6. The new micro flange grille is held in place by several small,  
powerful magnets on the speaker frame. Place the grille  
against the speaker and the magnets will hold it firmly in  
place. When properly installed, the grille flange should  
make contact with the wall all the way around the speaker.  
LCR2  
Tweeter:  
Midrange:  
1" (25mm) silk dome, ferrofluid-cooled  
4” (100mm) carbon fiber/Rohacell®  
laminated cone with a rubber  
surround  
Woofer:  
Four 5¼" (133mm) carbon fiber/  
Rohacell® laminated cones with  
rubber surrounds  
Painting the Speakers and Grilles  
Please refer to the included Painting Instructions sheet.  
Frequency Response:  
Impedance:  
70Hz – 20kHz 3dB  
6 ohms nominal; 4 ohms minimum  
5 watts minimum; 200 watts maximum  
92dB SPL (2.83V/1 meter)  
Perforated steel  
Specifications  
Power Handling:  
Sensitivity:  
LCR1  
Tweeter:  
1" (25mm) silk dome, ferrofluid-cooled  
Grille Material:  
Midrange:  
4” (100mm) carbon fiber/Rohacell®  
laminated cone with a rubber  
surround  
Dimensions (W x H x D): 8 7/8" x 34 7/8" x 3 7/8"  
(225mm x 886mm x 98mm)  
Cutout Dimensions (W x H): 7 ½" x 33 ½" (191mm x 851mm)  
Woofer:  
Two 5¼" (133mm) carbon fiber/  
Rohacell® laminated cones with  
rubber surrounds  
Shipping Weight:  
29 lbs (13.2kg) each  
Frequency Response:  
Impedance:  
70Hz – 20kHz 3dB  
SUR2  
6 ohms nominal; 4 ohms minimum  
5 watts minimum; 150 watts maximum  
90dB SPL (2.83V/1 meter)  
Perforated steel  
Tweeter:  
Two 1" (25mm) silk domes, ferrofluid-  
cooled  
Power Handling:  
Sensitivity:  
Midrange:  
Woofer:  
Two 3” (76mm) carbon fiber/  
Rohacell® laminated cones with  
rubber surrounds  
Grille Material:  
Dimensions (W x H x D): 8 7/8" x 21¾" x 3 7/8"  
Four 5¼" (133mm) carbon fiber/  
Rohacell® laminated cones with  
rubber surrounds  
(225mm x 553mm x 98mm)  
Cutout Dimensions (W x H): 7 ½" x 20½" (191mm x 521mm)  
Shipping Weight:  
19 lbs (8.6kg) each  
Frequency Response:  
Impedance:  
70Hz – 20kHz 3dB  
6 ohms nominal; 4 ohms minimum  
5 watts minimum; 200 watts maximum  
92dB SPL (2.83V/1 meter)  
Perforated steel  
Power Handling:  
Sensitivity:  
Grille Material:  
Dimensions (W x H x D): 8 7/8" x 34 7/8" x 3 7/8"  
(225mm x 886mm x 98mm)  
Cutout Dimensions (W x H): 7 ½" x 33 ½" (191mm x 851mm)  
Shipping Weight:  
29 lbs (13.2kg) each  
3
 
damage in transit is to be borne by the purchaser. If upon examina-  
tion at the factory or Authorized Sonance Dealer it is determined that  
the unit was defective in materials or workmanship at any time dur-  
ing this warranty period, Sonance or the Authorized Sonance Dealer  
will, at its option, repair or replace this product at no additional  
charge, except as set forth below. If this model is no longer available  
and can not be repaired effectively, Sonance, at is sole option, may  
replace the unit with a current model of equal or grater value. In  
some cases where a new model is substituted, a modification to the  
mounting surface may be required. If mounting surface modification  
is required, Sonance assumes no responsibility or liability for such  
modification. All replaced parts and product become the property of  
Sonance. Products replaced or repaired under this warranty will be  
returned to the original retail purchaser, within a reasonable time,  
freight prepaid.  
Technical Assistance and Service  
If you any have questions about the operation or installation  
of this product, please call our Technical Assistance  
Department on any business day at (800) 582-0772 or  
(949) 492-7777; from 7 a.m. to 5 p.m., PST.  
If your speakers should need repair or service, contact your Sonance  
Authorized Dealer for help, or use the following procedure:  
1. Prior to calling, note the products model number, serial number,  
purchase date, and the name and address of the dealer where you  
purchased the product.  
2. Contact our Technical Assistance Department at the above num-  
ber(s) and describe the problem the unit is experiencing. If appli-  
cable, they will issue a Return Authorization Number.  
IMPORTANT: YOU MUST HAVE PRIOR AUTHORIZATION TO  
RETURN YOUR SPEAKER TO SONANCE!  
This Warranty does not include service or parts to repair damage  
caused by accident, disaster, misuse, abuse, negligence, inadequate  
packing or shipping procedures, commercial use, voltage inputs in  
excess of the rated maximum of the unit, or service, repair or modi-  
fication of the product which has not been authorized or approved  
by Sonance. This Warranty also excludes normal cosmetic deteriora-  
tion caused by environmental conditions. This Warranty will be void  
if the Serial Number on the product has been removed, tampered-  
with or defaced. This Warranty is in lieu of all other expressed war-  
ranties. If the product is defective in materials or workmanship as  
warranted above, the purchasers sole remedy shall be repair or  
replacement as provided above. In no event will Sonance be liable  
for any incidental or consequential damages arising out of the use or  
inability to use the product, even if Sonance or an Authorized  
Sonance Dealer has been advised of the possibility of such damages,  
or for any claim by any other party.  
3. If you’re directed to return the unit to Sonance for repair, pack the  
unit in its original shipping carton. If needed, you can obtain  
replacement packaging from us for a small charge. Note: it is best  
if you place the box into an additional outer “overcarton” before  
shipment to minimize a chance of theft in shipment. Please include  
a copy of the original bill of sale inside the package.  
4. Contact a package delivery company such as United Parcel  
Service or Federal Express to arrange prepaid (not collect)  
shipping. Do not use the U.S. Postal Service.  
IMPORTANT: Freight collect shipments will be refused.  
5. Write the Return Authorization Number on the outside of  
the shipping carton.  
6. Ship the packaged unit to:  
Some states do not allow the exclusion or limitation of consequential  
damages, so the above limitation and exclusion may not apply. All  
implied warranties on the product are limited to the duration of this  
expressed Warranty. Some states do not allow limitation on the  
length of an implied warranty. If the original retail purchaser resides  
in such a state, this limitation does not apply.  
Quality Assurance Department  
Sonance  
212 Avenida Fabricante  
San Clemente, CA 92672-7531  
Limited Lifetime Warranty Coverage  
(U.S. Only)  
Exclusions And Limitations  
Sonance warrants to the original retail purchaser only that  
this Sonance product will be free from defects in materials  
and workmanship, provided the speaker was purchased from  
a Sonance Authorized Dealer.  
The warranty set forth above is in lieu of all other warranties,  
express or implied, of merchantability, fitness for a particular pur-  
pose, or otherwise. The warranty is limited to Sonance products reg-  
istered herein and specifically excludes any damage to loudspeakers  
and other allied or associated equipment which may result for any  
reason from use with this product. Sonance shall, in no event, be  
liable for incidental or consequential damages arising from any  
breach of this warranty or otherwise. This warranty gives you specif-  
ic legal rights, and you may have other rights which vary from state  
to state.  
Defective products must be shipped, together with proof of purchase,  
prepaid insured to the Authorized Sonance Dealer from whom they  
were purchased, or to the Sonance factory at the address listed on  
this instruction manual. Freight collect shipments will be refused. It is  
preferable to ship this product in the original shipping container to  
lessen the chance of transit damage. In any case, the risk or loss or  
©2008 Sonance. All rights reserved. Sonance, Sonance Cinema and RotoLock are registered trademarks of Dana Innovations.  
Rohacell is a registered trademark of Degussa GmbH.  
Due to continuous product improvement, all features and specifications are subject to change without notice.  
SONANCE • 212 Avenida Fabricante • San Clemente, CA 92672-7531 USA  
(800) 582-7777 or (949) 492-7777 • FAX: (949) 361-5151 • Technical Support: (800) 582-0772  
33-4788  
09/08  
 

Shark Carpet Cleaner S3101UKM User Manual
Snapper Utility Vehicle 63151 User Manual
Sony Battery Charger ERA 301P4 User Manual
Sony Cell Phone 1289 3481 User Manual
Sony Clock Radio ICF C180 User Manual
Sony Universal Remote RM AV2000 User Manual
Sony Video Game Headset MDR RF920RK User Manual
Spectra Logic Network Card TAC COM SERIES User Manual
State Industries Water Heater SUF 130 300 User Manual
Sylvania Flat Panel Television 6427TEL User Manual