Sonance Network Router CB1 User Manual

33-1892 CB1-inst8-02.qxd 9/23/02 2:27 PM Page 1  
INSTALLATION INSTRUCTIONS  
CB1  
ONE ZONE CONNECTING BLOCK  
The Model CB1 provides a quick low cost means of  
connecting all Sonance IR Receivers and Keypads  
to four single or four dual emitters and a power  
supply in an infrared repeater system. It can also  
EMITTERS  
CB1  
ONE ZONE  
CONNECTING BLOCK  
provide a low cost means of emitter expansion in  
existing systems, or to connect multiple emitters at  
the output of other Sonance devices, such as the  
ACB1 Amplified Connecting Blocks.  
IR  
RCVR  
PWR  
Fig. 1 CB1 One Zone Connecting Block  
Mounted in 3SNAPTRACK™  
(SNAPTRACK is a registered trademark of AUGAT)  
SPECIFICATIONS  
• Inputs: 1-Screw type 4-terminal plug-in. 1-IR Receiver “IR RCVR” 3.5 mm stereo mini jack.  
• Outputs: 4-Emitter ports (3.5mm mono mini jacks) parallel driven.  
• Contains a 470 Ohm resistor in series with each emitter output.  
• Sonance E1, VE1, E2 & VE2 Mini Emitters may be used.  
• Power requirements: 12 volts DC. Uses PS1 or PS2 Power Supplies. NOTE: A power supply is not  
connected to the CB1 when it is used as an emitter expander.  
• 2.1 mm coaxial power jack.  
• Dimensions: 2-3/8" W x 3" D x 13/16" H.  
INSTALLATION  
Fig. 2, next page, illustrates a typical installation using the CB1 in an IR repeater system. A variety of  
Sonance IR Receivers are shown. When configuring a system, please keep the following items in mind:  
1. More IR Receivers may be wired in parallel, in the same manner as shown, up to a maximum of twelve.  
More than twelve is not recommended because IR noise picked up by the many IR receivers may cause  
erratic operation and reduce remote control range.  
2. Be sure to connect the +12V, Output, and GND of each IR Receiver and keypad to the respective  
+12VDC, SIGNAL, and GND of the connecting block as shown.  
3. Please Note:  
a) Each IR receiver draws 10 milliamps.  
b) The maximum current for proper operation from the PS1 Power Supply is 200 milliamps.  
c) The maximum current for proper operation from the PS2 Power Supply is 1000 milliamps.  
d) When using combinations of keypads and receivers, do not exceed the maximum current of the power  
supplies as noted above.  
For example, 6 receivers and 8 emitters could be used with one PS1 Power Supply. If the current  
capability of the PS1 will be exceeded, use the PS2 Power Supply instead.  
CAUTION: Do not use unregulated 12V power supply adapters from other manufacturers. These  
may deliver excessive voltage to the IR receivers and cause them to “latch-up”. When this occurs,  
the “talk-back” LEDs and VE1 Visible emitters (if used) will stay on continuously!  
4. For clarity, connections in this illustration are shown going to a 3-conductor bus in a "daisy chain"  
fashion. In an actual installation, however, it is recommended that 3-conductor "home-runs" be pulled from  
each room to the CB1 Connecting Block in the main room. This maintains higher power supply voltage to  
each IR receiver and keypad for best operation.  
5. The "IR RCVR" jack on the CB1 allows the SMR1P and the CR1 (with a 3.5 mm stereo mini plug) to be  
plugged directly into the CB1.You can do this when the CB1 Connecting Block is within reach of the 7-foot cable;  
such as when installing the SMR1P in a cabinet where the controlled equipment is behind closed doors.  
CAUTION: Plug only Sonance IR Receivers equipped with a stereo mini plug into the IR RCVR jack.  
Do not plug in emitters or other devices; to do so will destroy emitters and damage power supplies!  
6. The emitter ports are driven in parallel with a 470 Ohm resistor connected in series with each port. The  
resistors ensure proper current sharing to each emitter. When using less than 4 emitters, you may plug  
them into any of the 4 emitter ports without regard to order.  
Pg 1  
 

Sharp Air Cleaner LC0760 User Manual
Sharp PDAs Smartphones EL 6930 User Manual
Soleus Air Electric Heater HGW 308R User Manual
Sony Camera Lens DSC P71 User Manual
Sony Speaker A1327 User Manual
Sony Stereo Receiver 3 875 814 111 User Manual
Sony Stereo Receiver R DG1200 User Manual
StarTechcom Switch SV231DDUSB User Manual
Sunbeam Food Saver VS5200 User Manual
TANDBERG Network Card Gatekeeper User Manual