Shakespeare Electronic Radio Antenna 410 R User Manual

Style 410-R  
Supplied Parts  
Thank you for purchasing a Shakespeare antenna product.  
Customer comments are welcome. Before installing, please study  
the diagram and check parts supplied against those listed.  
1 Swivel Mount assembly  
1 Standoff Bracket assembly  
1 1“ Reducing adapter  
IMPORTANT! Please read all instructions  
before installing.  
1 11/8“ Reducing Adapter  
The Style 410-R Mounting Kit is a versatile antenna mounting  
kit comprised of a Shakespeare Style 81-S Swivel Mount and a  
Shakespeare Style 408-R Standoff Bracket. The dual swivel mount  
permits mounting on vertical or horizontal surfaces. For use with  
1½” antennas, and antennas of 11/8” and 1” diameter by using the  
appropriate adapter (supplied) in the standoff bracket.  
Retainer Bar  
STANDOFF  
BRACKET  
Wing Nut  
Reducing Adapter  
Antenna  
Standoff Bracket  
Assembly  
Tools required: Drill and drill bit for ¼” screws;  
screwdriver; wrench or pliers  
Installation Instructions  
Mounting  
Screw*  
Choose an antenna mounting location that is as high as feasible,  
as free as possible from obstructions, and as far as possible from  
other antennas and strong sources of RF.  
1. Using the base of the Swivel Mount as a template, mark the  
location for the four mounting holes. Drill ¼” holes.  
Note: When drilling fiberglass, place a wooden backup block  
behind the surface if possible, to minimize push-through  
damage.  
Washer*  
Nut*  
2. Attach the Swivel Mount to the mounting surface using  
hardware (sold separately) that is applicable to the mounting  
surface.  
Lockwasher*  
Nut*  
SWIVEL  
MOUNT  
Mounting Screw*  
IMPORTANT: If the thickness of the mounting  
surface is not adequate to support the antenna under  
expected stress, a wooden back-up pad (not supplied)  
should be applied underneath the mounting surface  
during installation.  
Lockwasher*  
1”-14 Thread  
Mount Base  
3. Assemble the antenna to the Swivel Mount, being careful not to  
damage the antenna’s cabling, if any.  
4. Loosen the wing nut on top of the Standoff Bracket and slide  
the retainer bar out of the way. Gently place the antenna in its  
mounting position in the U-shaped opening in the bracket. For  
11/8” and 1” antennas, put the appropriate reducing adapter  
(supplied) in the opening.  
5. Rotate the retainer bar over the antenna to lock it in place.  
6. Using the Standoff Bracket itself as a template, mark the position  
for its mounting holes.  
7. Drill ¼” mounting holes, and install the bracket using stainless  
steel hardware appropriate to the mounting surface (hardware  
sold separately).  
8. Tighten the wing nut to secure the antenna in the bracket. The  
completed installation should attach the antenna firmly to the  
mounting surface, leaving no “play” between the antenna and  
the standoff bracket.  
Swivel  
* Not supplied. For some types of mounting surfaces you might need  
stainless steel woodscrews or other hardware.  
Shakespeare Electronic Products Group  
Shakespeare is a subsidiary of Jarden Corporation (NYSE: JAH)  
©2002 Shakespeare Co.  
· Form I-410-R J: rev. 04/25/2010  
 

Sharp Stereo System CD ES777 User Manual
Sherwood CD Player V 903 User Manual
Shure Headphones 565d User Manual
Sony Bluetooth Headset BDV E2100 User Manual
Sony Cassette Player TC D6C User Manual
Sony Home Theater System DAV LF10 User Manual
Sony Indoor Furnishings XL 2100C User Manual
Stamina Products Elliptical Trainer 15 7250 User Manual
State Industries Water Heater SBD100400NE A User Manual
SUPER MICRO Computer Switch SSE G24 TG4 User Manual